Home Theater System Live

5 Responses to “SANUS SYSTEMS BF-16B 16″ Wood Speaker Stands”

1. Michael W. Thompson Says: August 25th, 2010 at 10:16 pm

   Buyers beware. I have a pair of Sanus 31″ speakers stands and wanted to reduce the height of the speakers. I got the “16″ inch stands and put them together. Sanus is not a poor stand, but not one of the best. When I got the stands assembled I realized that they were not 16″ high. When I measured them they stand just under 14 3/4″ from the bottom of the base to the top of the top platform. I know Amazon is good about returns, however taking them apart and going through the issues involved in returning them is not worth it. So, I’ll live with these, even though they are not the advertised dimensions.
   Rating: 2 / 5

2. Peter Keiper Says: August 26th, 2010 at 12:55 am

   You get what you pay for. When you pay less than $40 for speaker stands you aren’t going to get things like good materials or even reliable product descriptions.

   These things are made of something. Certainly not wood.

   It is *very* easy to split the material when you are putting it together if you are not careful.

   They are not 16″ tall. As another reviewer also noted. They are at least an inch shorter than that. Keep that in mind as well.

   The “wire management” is a joke. There is a hole in the bottom of the base but then there is no groove to route the wire once it gets out so the base ends up on top of it. Very poor design.

   So it loses a star for the material, the lie on the height and the wire management issue.

   It gets a star for holding up the speakers and another for being cheap and easy to put together.

   Any way you slice it. Two Stars.

   I got these to hold up my mids in a 7.1 system. For that they are fine.
   Rating: 2 / 5

3. A. Dent Says: August 26th, 2010 at 3:30 am

   Briefly:
   
   ——–
   
   I ordered these stands to hold a pair of satellite speakers on a 7.1 setup and I am using them but the few design flaws have created major problems and, while I am using them now, I would not order them today, knowing what I know now.

   But, here it is, what I hope is an objective review.

   Packaging:
   
   ———-
   
   They were delivered in a nice box. All parts were packed tight and secure with all wooden panels well protected against scratches.

   Assembly:
   
   ———
   
   It shouldn’t take longer than 30 minutes. It basically consists on attaching the 2 pillars to the base and then adding the top to the assembly. It’s 8 screws per stand. A Phillips screwdriver is needed.

   I was impressed how everything fit perfectly. There were no chips, cracks or scratches.

   Looks:
   
   ——
   
   These are surprisingly good-looking if black finish is what you need. To the extent that you can avoid chipping on scratching them, they don’t look ‘cheap’ at all.

   The bottom place allows for the speaker wire to come from underneath but there’s no groove so, if you are placing the stand on a hard floor, it would destabilize it but carpets should be okay. Plastic wire covers will hide the wires if anyone would ever look ‘behind’ the speaker.

   Here are the dimensions:

   Height – 14.75″
   
   Base – 12″ x 10.5″
   
   Top plate – 7″ x 7″

   Made in Malaysia.

   Design Flaws:
   
   ————-

   * HEIGHT *
   
   Everyone should be aware that these stands are NOT 16″ tall. They are under 15″.

   * BASE*
   
   There is no way you can hide the wire by running it under the base because there is no groove carved in the base for that purpose. If the stand sits on a flat, hard surface such as a wood floor running a wire underneath would destabilize the stand. If the stand sits on a carpet you MIGHT be able to squeeze a thin wire under, if you are using the provided spikes.

   * WIRE PATH *
   
   Assuming that you found a way to run the wire under the base, you will find that it’s impossible to pass it through the speaker platform hole, unless it’s very thin. It was impossible to run a 16 gauge speaker wire through that hole.

   * SPEAKER PLATFORM *
   
   If you wire was thin enough to pass through the wall, you will have to deal with the hole being in the center of the platform. The only way you can have the wire going through that hole without destabilizing the speaker is by placing the speaker on its back, facing the ceiling or, if the speakers are small enough, place them on the front half of the platform, possibly destabilizing the stand.

   I am currently using these stands in the same way I’d be using a stool to hold the speakers. The wire does not go underneath the base and it does not pass through the holes in the base or the speaker platform. There are no mounting options but I manage to keep the speaker in place with a little Velcro – it works.

   Overall:
   
   ——–
   
   Even though the packaging is tight, the assembly is easy and the materials appear to be of good quality I would not order stands of this design again for the reasons I stated above. Therefore, a 2-star rating is warranted because in Amazon’s rating system 3 stars mean ‘I like it’ and I don’t.
   Rating: 2 / 5

4. Aaron Williams Says: August 26th, 2010 at 6:15 am

   These are fine. They hold up the speaker. There are little plastic pegs that go into the bottom of the stand for carpet, one of them broke while i was trying to insert it into the base.
   Rating: 4 / 5

5. FrogThinker Says: August 26th, 2010 at 7:39 am

   This is a good value for the money (with the current discount at 22$). The plastic cover that hides the cable is too short and does not hide the cable all the way, not a big deal but not perfect. Quality matches the price but they look nice.
   Rating: 4 / 5

Leave a Reply